Tsunesaburo kanna restoration: 2. The blade/iron and chipbreaker

This post details restoration of a kanna by Tsunesaburo and continues from Part 1.
I correct the ‘ears’ on the blade with a white wheel on a stationary bench grinder. I make sure to mark the width I need to go to on each side first; then, at the machine, I just take it slow and use water as a coolant. I should also add I freehand this. Using some form of a jig, or at least a tool rest, will no doubt allow more consistent and repeatable results than mine. Even with my crude, simple technique the blade soon starts looking much better.
Bearded Witch Tsunesaburo-10

Most importantly, the edge is now centred. I grind a bit more than I need since I will be removing the chips in the edge and increasing the bevel angle, therefore shortening the blade. This will widen the edge again. I may need to fine tune it later. This is an ongoing maintenance aspect anyway and is very quick to do.

While at the grinder, I also take off the mushroomed sections at the top of the iron and the chipbreaker. This is a bit awkward to do since visibility is greatly reduced at the angle you need to hold the blade at (unless you want to introduce a bevel).  If you fancy giving one of your kannas a similar treatment but feel a bit apprehensive, you can just forego the grinder and use a file. The top half of your kanna will be made of either soft steel or iron, and will be very easy to work by hand.

BBW Tsunesaburo Part 2-2

Straight off the grinder

After grinding, I finesse the surface slightly with a second cut metal file. My intention is to rust blue the exposed bare metal later in order to somewhat blend these areas in.

BBW Tsunesaburo Part 2-3

After filing

I now turn my attention to the edge itself, and that shallow bevel angle. My first concern is to widen the flat on the back of the blade. I alternate tapping out with lapping on a medium stone. I prefer to take things gradually, and once I recover a couple of millimetres, I start on the bevel.

BBW Tsunesaburo Part 2-15

The bevel angle is a big job. I prefer to do it by hand, with the blade in a guide and on a rough stone.

BBW Tsunesaburo Part 2-20

An audiobook keeps me company; this takes a significant amount of time and effort. An aggressive and firm stone helps.

BBW Tsunesaburo Part 2-18

The chips are gone; a long way still ahead for this bevel

As the angle on the bevel starts building up, and the blade shortens, I return to the anvil for more tapping out and some lapping on the back again. I then alternate the tapping out and lapping the back with longer sessions of working on the bevel. This steel is hard and tenacious…

BBW Tsunesaburo Part 2-22

It is important to note that this blade took a lot of tapping. The very shallow angle made the bevel long and thin; my feeling is that this may present an increased risk of cracking the blade. In any case, I try and spread the taps over a wider area to ‘massage’ the steel forward gradually, and cushion the steel side (I just use a folded card or newspaper).

BBW Tsunesaburo Part 2-1

It is also important to note that it is not strictly necessary to establish the full length of the bevel at the new angle – and it can be argued that it is somewhat wasteful to rid the blade of precious hard steel in the process. I do it in this case but I would be happy to settle on maybe 3/4 length or so for practical reasons. Once I am satisfied with the bevel geometry, I correct the ears once again. I fine tune them with a medium synthetic stone.

I then take the blade through my sharpening procedure to work up a fine finish.

BBW Tsunesaburo Part 2-26

Ready to take to the finishing stone

As I noted in the previous post, the chipbreaker already has its geometry set up to my liking and, as a result, is fairly straightforward to prepare. It is an absolute pleasure to see a chipbreaker of this quality; it is of meticulously laminated steel construction and inspires 100% confidence. It aspires to be treated as equal to the main blade.

I flatten the back (including minor tapping out in one corner), and then work up the finish up to my fine stone.

BBW Tsunesaburo Part 2-28

Just off the medium stone

I work on the back, the main bevel and the micro bevel.

BBW Tsunesaburo Part 2-29

The last step: polishing the microbevel

In the next, last instalment, I will look at fitting the chipbreaker to the blade, and correcting the dai. Stay tuned!

 

7 thoughts on “Tsunesaburo kanna restoration: 2. The blade/iron and chipbreaker

  1. Nice dai. Too bad about the gouge marks. You might consider using an epoxy bedding compound colored to match the wood to fill those holes, although they probably won’t negatively influence performance.

    Keep up the great work! Stan

    Liked by 1 person

      1. In my experience it depends on the stone. I have a kiita that makes it *relatively* easy, and Aizu and Tsushima are good for it in lower grits. Still prefer pure carbon, though. 🙂

        Like

  2. I have had Super Blue blades in the past, buy have since dumped them. Hard to settle on anything other than Shirgoami No. 1 or Aogmai No.2 anymore. Super Blue is just too irritating to sharpen, IMO.

    Like

    1. Thank you for sharing that, Stan. As I mentioned I too have a preference for the ‘regular’ (Super-less) kanna, and especially WS/Swedish/Inukubi variety. I hope I did not sound arrogant at any point, it was not until I found a stone that is a wonderful match for BSS that I truly started enjoying sharpening of BSS kannas.

      Liked by 1 person

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s